This is a Vive basic package 8A switch and corner sensor. The Maestro Wireless solution incorporates Maestro Wireless load controls, wireless sensors, and wireless remote controls, which provide a system that delivers energy savings, convenience, and ease of installation. Maestro Wireless dimmers and switches use Lutron patented Clear Connect RF Technology, which enables wireless communication with Radio Powr Savr sensors and Pico remote controls for light control and general switched loads. These products are also compatible with the Vive hub which enables a simple setup process using a standard web browser on any Wi-Fi enabled phone, tablet or computer. It also enables control and monitoring of all Vive devices. The Vive hub can be added at any time and preserves existing system setup by extracting local programming from each device. For a complete list of features supported with the Vive hub, call Lite Rite Controls. Note for Replacement: MRF2S – the “S” model can replace the non-”S” model. Click here to see the Lutron Vive story.

HIGHLIGHTS:

• The Vive Basic package 8A switch and corner sensor provides switching and occupancy / vacancy sensing.
• Lutron patented Clear Connect RF Technology works through walls and floors.
• Controls include Front Accessible Service Switch (FASSTM) for safe lamp replacement.
• Two-wire installation for any retrofit application.
• Power failure memory: If power is interrupted, the control will return to its previously set level prior to interruption.

System Communications and Capacity

• Maestro Wireless controls communicate with the Pico remote controls and Radio Power Savr
• sensors through radio frequency (RF).
• Receives wireless inputs from up to 10 Pico remote controls, 10 Radio Powr Savr occupancy / vacancy sensors, and 1 Radio Powr Savr daylight sensor
• Maestro Wireless local controls must be located within 60 ft. (18 m) line of sight or 30 ft. (9 m) through walls, of Radio Power Savr sensors.
• Maestro Wireless local controls must be located within 60 ft. (18 m) line of sight or 30 ft. (9 m)
• through walls, of a Pico remote control.
• Up to 10 Maestro Wireless controls can be configured to work together.

Sensors can be assigned to multiple switches.

This is a Vive basic package 8A switch and wall sensor. The Maestro Wireless solution incorporates Maestro Wireless load controls, wireless sensors, and wireless remote controls, which provide a system that delivers energy savings, convenience, and ease of installation. Maestro Wireless dimmers and switches use Lutron patented Clear Connect RF Technology, which enables wireless communication with Radio Powr Savr sensors and Pico remote controls for light control and general switched loads. These products are also compatible with the Vive hub which enables a simple setup process using a standard web browser on any Wi-Fi enabled phone, tablet or computer. It also enables control and monitoring of all Vive devices. The Vive hub can be added at any time and preserves existing system setup by extracting local programming from each device. For a complete list of features supported with the Vive hub, call Lite Rite Controls. Note for Replacement: MRF2S – the “S” model can replace the non-”S” model. Click here to see the Lutron Vive story.

HIGHLIGHTS:

• The Vive basic package 8A switch and wall sensor provides switching and occupancy / vacancy sensing.
• Lutron patented Clear Connect RF Technology works through walls and floors.
• Controls include Front Accessible Service Switch (FASSTM) for safe lamp replacement.
• Two-wire installation for any retrofit application.
• Power failure memory: If power is interrupted, the control will return to its previously set level prior to interruption.

System Communications and Capacity

• Maestro Wireless controls communicate with the Pico remote controls and Radio Power Savr
• sensors through radio frequency (RF).
• Receives wireless inputs from up to 10 Pico remote controls, 10 Radio Powr Savr occupancy / vacancy sensors, and 1 Radio Powr Savr daylight sensor
• Maestro Wireless local controls must be located within 60 ft. (18 m) line of sight or 30 ft. (9 m) through walls, of Radio Power Savr sensors.
• Maestro Wireless local controls must be located within 60 ft. (18 m) line of sight or 30 ft. (9 m)
• through walls, of a Pico remote control.
• Up to 10 Maestro Wireless controls can be configured to work together.
• Sensors can be assigned to multiple switches.

This is a Vive basic kit 2S10W which includes 2-8a switches and a wall sensor. The Maestro Wireless solution incorporates Maestro Wireless load controls, wireless sensors, and wireless remote controls, which provide a system that delivers energy savings, convenience, and ease of installation. Maestro Wireless dimmers and switches use Lutron patented Clear Connect RF Technology, which enables wireless communication with Radio Powr Savr sensors and Pico remote controls for light control and general switched loads. These products are also compatible with the Vive hub which enables a simple setup process using a standard web browser on any Wi-Fi enabled phone, tablet or computer. It also enables control and monitoring of all Vive devices. The Vive hub can be added at any time and preserves existing system setup by extracting local programming from each device. For a complete list of features supported with the Vive hub, call Lite Rite Controls. Note for Replacement: MRF2S – the “S” model can replace the non-”S” model. Click here to see the Lutron Vive story.

HIGHLIGHTS:

• The Vive Basic Kit 2S10W provides switching and occupancy / vacancy sensing of multiple load types.
• Lutron patented Clear Connect RF Technology works through walls and floors.
• Controls include Front Accessible Service Switch (FASSTM) for safe lamp replacement.
• Two-wire installation for any retrofit application.
• Power failure memory: If power is interrupted, the control will return to its previously set level prior to interruption.

System Communications and Capacity

• Maestro Wireless controls communicate with the Pico remote controls and Radio Power Savr sensors through radio frequency (RF).
• Receives wireless inputs from up to 10 Pico remote controls, 10 Radio Powr Savr occupancy / vacancy sensors, and 1 Radio Powr Savr daylight sensor.
• Maestro Wireless local controls must be located within 60 ft. (18 m) line of sight or 30 ft. (9 m) through walls, of Radio Power Savr sensors.
• Maestro Wireless local controls must be located within 60 ft. (18 m) line of sight or 30 ft. (9 m) through walls, of a Pico remote control.
• Up to 10 Maestro Wireless controls can be configured to work together.
• Sensors can be assigned to multiple switches.

This is a Vive Maestro wireless switch. The Maestro Wireless solution incorporates Maestro Wireless load controls, wireless sensors, and wireless remote controls, which provide a system that delivers energy savings, convenience, and ease of installation. Maestro Wireless dimmers and switches use Lutron patented Clear Connect RF Technology, which enables wireless communication with Radio Powr Savr sensors and Pico remote controls for light control and general switched loads. These products are also compatible with the Vive hub which enables a simple setup process using a standard web browser on any Wi-Fi enabled phone, tablet or computer. It also enables control and monitoring of all Vive devices. The Vive hub can be added at any time and preserves existing system setup by extracting local programming from each device. For a complete list of features supported with the Vive hub, call Lite Rite Controls. Note for Replacement: MRF2S – the “S” model can replace the non-”S” model. Click here to see the Lutron Vive story.

HIGHLIGHTS:

• The Vive Maestro Wireless switch provides switching of multiple load types and high-end trim.
• Lutron patented Clear Connect RF Technology works through walls and floors.
• Incorporates advanced features such as fade ON/fade OFF, high-end trim, and rapid full-ON.
• Controls include Front Accessible Service Switch (FASSTM) for safe lamp replacement.
• Two-wire dimmers and switches available for retrofit applications.
• Power failure memory: If power is interrupted, the control will return to its previously set level prior to interruption.

Ganging and Derating

When combining controls in the same wallbox, derating is required. See pdf spec sheet for more info.

Mixing Lamp Types

Mixing lamp types (using a combination of CFL/LED, and Incandescent/Halogen bulbs) and ganging with other dimmers or electronic switches may reduce maximum wattage, as shown. Example: If fins from one side of dimmer are removed and you have two 24 W bulbs installed (total CFL Wattage = 48 W), you may add up to 300 W of incandescent or halogen lighting.

This is a Vive Maestro wireless electronic low voltage dimmer; neutral required. The Maestro Wireless solution incorporates Maestro Wireless load controls, wireless sensors, and wireless remote controls, which provide a system that delivers energy savings, convenience, and ease of installation. Maestro Wireless dimmers and switches use Lutron patented Clear Connect RF Technology, which enables wireless communication with Radio Powr Savr sensors and Pico remote controls for light control and general switched loads. These products are also compatible with the Vive hub which enables a simple setup process using a standard web browser on any Wi-Fi enabled phone, tablet or computer. It also enables control and monitoring of all Vive devices. The Vive hub can be added at any time and preserves existing system setup by extracting local programming from each device. For a complete list of features supported with the Vive hub, call Lite Rite Controls. Note for Replacement: MRF2S – the “S” model can replace the non-”S” model. Click here to see the Lutron Vive story.

HIGHLIGHTS:

• The Vive Maestro wireless electronic low voltage dimmer provides dimming of multiple load types.
• Lutron patented Clear Connect RF Technology works through walls and floors.
• Incorporates advanced features such as fade ON/fade OFF, high-end trim, and rapid full-ON.
• Controls include Front Accessible Service Switch (FASSTM) for safe lamp replacement.
• Two-wire dimmers and switches available for retrofit applications.
• Power failure memory: If power is interrupted, the control will return to its previously set level prior to interruption.

Ganging and Derating

When combining controls in the same wallbox, derating is required. See pdf spec sheet for more info.

Mixing Lamp Types

Mixing lamp types (using a combination of CFL/LED, and Incandescent/Halogen bulbs) and ganging with other dimmers or electronic switches may reduce maximum wattage, as shown. Example: If fins from one side of dimmer are removed and you have two 24 W bulbs installed (total CFL Wattage = 48 W), you may add up to 300 W of incandescent or halogen lighting.

This is a Vive Maestro wireless 8 amp switch. The Maestro Wireless solution incorporates Maestro Wireless load controls, wireless sensors, and wireless remote controls, which provide a system that delivers energy savings, convenience, and ease of installation. Maestro Wireless dimmers and switches use Lutron patented Clear Connect RF Technology, which enables wireless communication with Radio Powr Savr sensors and Pico remote controls for light control and general switched loads. These products are also compatible with the Vive hub which enables a simple setup process using a standard web browser on any Wi-Fi enabled phone, tablet or computer. It also enables control and monitoring of all Vive devices. The Vive hub can be added at any time and preserves existing system setup by extracting local programming from each device. For a complete list of features supported with the Vive hub, call Lite Rite Controls. Note for Replacement: MRF2S – the “S” model can replace the non-”S” model. Click here to see the Lutron Vive story.

HIGHLIGHTS:

• The Vive Maestro Wireless 8 amp switch provides switching of multiple load types.
• Lutron patented Clear Connect RF Technology works through walls and floors.
• Incorporates advanced features such as fade ON/fade OFF, high-end trim, and rapid full-ON.
• Controls include Front Accessible Service Switch (FASSTM) for safe lamp replacement.
• Two-wire dimmers and switches available for retrofit applications.
• Power failure memory: If power is interrupted, the control will return to its previously set level prior to interruption.

Ganging and Derating

When combining controls in the same wallbox, derating is required. See pdf spec sheet for more info.

Mixing Lamp Types

Mixing lamp types (using a combination of CFL/LED, and Incandescent/Halogen bulbs) and ganging with other dimmers or electronic switches may reduce maximum wattage, as shown. Example: If fins from one side of dimmer are removed and you have two 24 W bulbs installed (total CFL Wattage = 48 W), you may add up to 300 W of incandescent or halogen lighting.

This is a Vive Maestro dual voltage wireless 8A switch; no neutral required. The Maestro Wireless solution incorporates Maestro Wireless load controls, wireless sensors, and wireless remote controls, which provide a system that delivers energy savings, convenience, and ease of installation. Maestro Wireless dimmers and switches use Lutron patented Clear Connect RF Technology, which enables wireless communication with Radio Powr Savr sensors and Pico remote controls for light control and general switched loads. These products are also compatible with the Vive hub which enables a simple setup process using a standard web browser on any Wi-Fi enabled phone, tablet or computer. It also enables control and monitoring of all Vive devices. The Vive hub can be added at any time and preserves existing system setup by extracting local programming from each device. For a complete list of features supported with the Vive hub, call Lite Rite Controls. Note for Replacement: MRF2S – the “S” model can replace the non-”S” model. Click here to see the Lutron Vive story.

HIGHLIGHTS:

• The Vive Maestro dual voltage wireless 8A switch provides switching of multiple load types.
• Lutron patented Clear Connect RF Technology works through walls and floors.
• Incorporates advanced features such as fade ON/fade OFF, high-end trim, and rapid full-ON.
• Controls include Front Accessible Service Switch (FASSTM) for safe lamp replacement.
• Two-wire dimmers and switches available for retrofit applications.
• Power failure memory: If power is interrupted, the control will return to its previously set level prior to interruption.

Ganging and Derating

When combining controls in the same wallbox, derating is required. See pdf spec sheet for more info.

Mixing Lamp Types

Mixing lamp types (using a combination of CFL/LED, and Incandescent/Halogen bulbs) and ganging with other dimmers or electronic switches may reduce maximum wattage, as shown. Example: If fins from one side of dimmer are removed and you have two 24 W bulbs installed (total CFL Wattage = 48 W), you may add up to 300 W of incandescent or halogen lighting.

This is the Touche Master Interface.

• Master Interfaces provide coordinated control for all of the system’s connected devices and act as a “gateway” to an Ethernet network.
• Up to (100) directly connected devices can be controlled by one Master Interface. If Multi-Function Interfaces are implemented up to (3200) devices can be controlled by one Master Interface.
• Auto-addressing of all connected devices is coordinated by the Master Interface.
• Both static and dynamic IP addressing is permitted for simple and adaptable setup when Ethernet communication is required.
• The Master Interface monitors the status of all connected devices, displays that information locally, and forwards relevant information to the programming application when appropriate.

• Provides switching of multiple load types, occupancy/vacancy sensing, and daylight harvesting.
• RF Technology works through walls and floors.
• Two-wire switch perfect for retrofit applications.
• Power failure memory: If power is interrupted, the control will return to its previously set level prior to interruption.

• Provides capability for a zone on a GRAFIK Eye control unit (or other product) to dim a fully loaded circuit of lighting.
• May be used to control incandescent, electronic low-voltage, magnetic low-voltage, and neon/cold cathode lighting sources, as well as Lutron Tu-Wire fluorescent dimming ballasts.
• Automatically selects leading-edge or trailing-edge dimming for low-voltage transformers.
• Provides power and dimming for one zone.
• Up to 3 power modules may be wired on a single GRAFIK Eye zone.

• Provides capability for a zone on a GRAFIK Eye control unit (or other product) to dim a fully loaded circuit of lighting.
• May be used to control incandescent, electronic low-voltage, magnetic low-voltage, and neon/cold cathode lighting sources, as well as Lutron Tu-Wire fluorescent dimming ballasts.
• Automatically selects leading-edge or trailing-edge dimming for low-voltage transformers.
• Provides power and dimming for one zone.
• Up to 3 power modules may be wired on a single GRAFIK Eye zone.

Mounting Considerations:

• Mounting of any RF devices on or in close proximity to a metal surface will drastically reduce the effective range of radio signal transmission or reception.
• All RF devices must be mounted on non-conductive materials to ensure proper performance.
• If you wish to mount your PicoR wireless control to a metal surface, the PICO-MOUNT-1-XX-CPN5733 will be required in order to maintain proper RF performance.