This is the digital forward phase dimming room controllers (LMRC-221, LMRC-222). LMRC-220 Series Digital Room Controllers include one or two output(s) to control a total of up to 20 amps. Load ratings include incandescent, magnetic low voltage, forward phase compatible electronic low voltage and LED drivers, neon and cold cathode, and dimmable two-wire and three-wire fluorescent ballasts. They are the foundation of a WattStopper Digital Lighting Management (DLM) system, and allow integration of occupancy sensors, daylighting controls and switches for energy-efficient lighting control. Check out Wattstopper DLM products here.

FEATURES:

• Plug n’ Go™ automatic configuration for quick installation and maximum energy savings
• Push n’ Learn™ functionality for personalization without the need for tools or a PC
• Digital Lighting Management components plug together on free-topology Cat 5e DLM local network
• On/Off/Dim local override button for each load
• LED indicates status of each load
• Integral current monitoring of total connected load
• Optional lamp burn in; 12 or 100 hours
• Square law, 2-wire and 3-wire fluorescent/LED curves
• 4 RJ45 ports with integral strain relief
• Zero-crossing circuitry for each relay for reliability and increased product life
• UL 2043 plenum rated
• RoHS compliant

Wallbox Power Module

The Wallbox Power Module controls up to six zones of light and will operate the following sources with a continuous Square Law dimming curve or on a full conduction non-dim basis:

Check out the RadioRA 2 collection here.

• Incandescent
• LED
• Tungsten Halogen
• Electronic Low-Voltage (ELV)
• Magnetic Low-Voltage (MLV) Transformer
• Metal Halide / High Pressure Sodium Switched
• Neon/Cold Cathode
• LutronR Tu-WireR Electronic Fluorescent Dimming Ballasts
• Approved LED and CFL lamps / fixtures
• Up to 64 DALI compliant output devices (devices must comply with IEC/EN 60929) can be addressed and grouped into zones (LQRK-WPM-6D and LQR-WPM-6D only). The Power Module can be configured for wired, QS link (HomeWorksR QS only), or wireless, RF link (HomeWorksR QS and RadioRAR 2), communication.

This is the RadioRA 2 visor control transmitter. RadioRA 2 Visor Controls allow lights, shades /draperies, and other equipment to be controlled from the car with just a touch of a button on a Visor Control Transmitter or a HomeLink® compatible visor control. Up to ten (10) Transmitters can be used with a Visor Control Receiver. Pre-printed and blank labels are included with the Visor Controls for naming scenes or buttons on both the Receiver and the Transmitter. Check out the RadioRA 2 products page here.

• Each output can be controlled locally at the Receiver or remotely by a Transmitter or keypad button.
• The Receiver ‘Keypad’ or ‘Inputs’ buttons can be programmed to light and shades /draperies. Design Features
• Full or Flash security options.
• The Transmitter can remotely control the ‘Keypad’, ‘Security Input’, and ‘Outputs’ buttons on the Receiver.
• RR-VCRX-WH:  Visor Control Receiver (Sold Separately)

This is the HVAC Controller & Wireless Temperature Sensor. Check out the RadioRA 2 collection here.

System package includes:
-1 HVAC Controller
-1 Wireless Temperature Sensor*
– 1 Wired Return Air Duct Sensor

The is the °F seeTEMP Wall Control, HVAC controller & Wireless Temperature Sensor. Check out the RadioRA 2 collection here.

System package includes:
-1 HVAC Controller
-1 seeTemp Wall Display (°F) (WH)
-1 Wireless Temperature Sensor (SW)
– 1 Wired Return Air Duct Sensor

This is the seeTemp Wall Display °C. Check out the RadioRA 2 collection here.

• Designer or Architectural style opening that can be ganged with other devices like dimmers and keypads.
• Installs in a standard wallbox for low-profile appearance.
• Multiple seeTemp TM Wall Displays can be used to control 1 HVAC Controller or TouchPRO Wireless TM Thermostat from multiple locations.

This is the seeTemp Wall Display Fahrenheit. Check out the RadioRA 2 collection here.

• Designer or Architectural style opening that can be ganged with other devices like dimmers and keypads.
• Installs in a standard wallbox for low-profile appearance.
• Multiple seeTemp TM Wall Displays can be used to control 1 HVAC Controller or TouchPRO Wireless TM Thermostat from multiple locations.

This is the Local Relay Module w/ optional, 2-channel, 0-10V Dimming.

• Provide a distributed control solution which allows the installer to place the module in close proximity to the controlled load.
• Can be connected directly to a master interface or through multi-function interfaces.
• Local Relay Modules each encompass (2) latching (mechanically held) single pole relays and each module incorporates the latest in “zero-cross” switching technology for improved equipment life.
• Include (3) “smart ports.” Each smart port provides a daisy-chained connection for up to (8) smart devices and are connected to the Local Relay Modules via standard Cat5 patch cables.

Build your smart lighting system with as few or as many products as you’d like. A kit is the easiest way to begin, but you can also purchase products individually and mix and match them. You can add more products to your system at any time.

• 1 Smart Bridge
• 2 Dimmers
• 2 Pico Remotes
• 2 Pedestals
• 2 Wallplates

The MP20 power/relay pack and MSP20 secondary relay pack work with low voltage occupancy sensors to
switch lighting loads on and off. The MP20 also transforms 120, 240, and 277 VAC single phase power
to Class 2 15 VDC to power remote sensors. Although plenum rated, the elongated mounting nipple
allows for these packs to be mounted either directly through a 1/2 inch knockout in a junction box,
or to be located inside an adjacent box for specific local code requirements. Up to 14 sensors may
be connected to one MP20. Multi-circuit control can be handled by multiple MP20 or MSP20
packs. MP20s can be wired continuously hot (line side), itch leg (load side) without nuisance
delays upon turn on.

FEATURES

• Powers Low Voltage Sensors (MP20)
• Switches Line Voltage Loads
• Plenum Rated

This is a Vive Basic Package 8 Amp Radio Powr Savr Switch & Ceiling Sensor. The Maestro Wireless solution incorporates Maestro Wireless load controls, wireless sensors, and wireless remote controls, which provide a system that delivers energy savings, convenience, and ease of installation. Maestro Wireless dimmers and switches use Lutron patented Clear Connect RF Technology, which enables wireless communication with Radio Powr Savr sensors and Pico remote controls for light control and general switched loads. These products are also compatible with the Vive hub which enables a simple setup process using a standard web browser on any Wi-Fi enabled phone, tablet or computer. It also enables control and monitoring of all Vive devices. The Vive hub can be added at any time and preserves existing system setup by extracting local programming from each device. For a complete list of features supported with the Vive hub, call Lite Rite Controls. Note for Replacement: MRF2S – the “S” model can replace the non-”S” model. Click here to see the Lutron Vive story.

Features:

• The Vive Basic Package 8 Amp Radio Powr Savr Switch & Ceiling Sensor.
• Lutron® patented Clear Connect® RF Technology works through walls and floors.
• Controls include Front Accessible Service Switch (FASS™) for safe lamp replacement.
• Two-wire installation for any retrofit application.
• Power failure memory: If power is interrupted, the control will return to its previously set level prior to interruption.

This is a Vive basic package 8 Amp switch & hallway sensor. The Maestro Wireless solution incorporates Maestro Wireless load controls, wireless sensors, and wireless remote controls, which provide a system that delivers energy savings, convenience, and ease of installation. Maestro Wireless dimmers and switches use Lutron patented Clear Connect RF Technology, which enables wireless communication with Radio Powr Savr sensors and Pico remote controls for light control and general switched loads. These products are also compatible with the Vive hub which enables a simple setup process using a standard web browser on any Wi-Fi enabled phone, tablet or computer. It also enables control and monitoring of all Vive devices. The Vive hub can be added at any time and preserves existing system setup by extracting local programming from each device. For a complete list of features supported with the Vive hub, call Lite Rite Controls. Note for Replacement: MRF2S – the “S” model can replace the non-”S” model. Click here to see the Lutron Vive story.

HIGHLIGHTS:

• The Vive basic package 8 Amp switch & hallway sensor provides switching and occupancy / vacancy sensing.
• Lutron patented Clear Connect RF Technology works through walls and floors.
• Controls include Front Accessible Service Switch (FASSTM) for safe lamp replacement.
• Two-wire installation for any retrofit application.
• Power failure memory: If power is interrupted, the control will return to its previously set level prior to interruption.

System Communications and Capacity

• Maestro Wireless controls communicate with the Pico remote controls and Radio Power Savr
• sensors through radio frequency (RF).
• Receives wireless inputs from up to 10 Pico remote controls, 10 Radio Powr Savr occupancy / vacancy sensors, and 1 Radio Powr Savr daylight sensor
• Maestro Wireless local controls must be located within 60 ft. (18 m) line of sight or 30 ft. (9 m) through walls, of Radio Power Savr sensors.
• Maestro Wireless local controls must be located within 60 ft. (18 m) line of sight or 30 ft. (9 m)
• through walls, of a Pico remote control.
• Up to 10 Maestro Wireless controls can be configured to work together.
• Sensors can be assigned to multiple switches.