This is the PIR wall switch occupancy sensor. The RS-250 Passive Infrared (PIR) Occupancy Sensor provides automatic lighting shutoff for single-pole lighting control applications. It offers optional automatic lighting activation.

The RS-250 operates either as a manual- or automatic-on sensor. When in manual-on mode, users must press the pushbutton to turn on lighting. The RS-250 employs PIR technology to sense the difference between the infrared energy from a person in motion and the background space. It keeps lighting on as long as motion is detected and provides automatic shutoff, following a user-selected time delay, when motion is no longer detected. Users may turn the lighting off manually.

When automatic-on operation has been selected, the adjustable light level sensor may be set to prevent lights from turning on automatically if sufficient daylight is present. Check out Wattstopper DLM products here.

• Complies with 2011 NEC requirements
• Replaces single-pole switches
• Adjustable time delay, 15 seconds to 30 minutes
• Lighted switch for visibility in darkened rooms
• If enabled, light level sensing prevents automatic-on when adequate daylight exists
• Low-profile styling
• Choice of five decorator colors; lens is color-matched to device
• Operates most common types of lighting
• Relay-based switching
• No current leakage to load in off mode for safety
• Compatible with decorator wall plates
• Compliant with Nonresidential CA Title 24 requirements

This is the Two-Pole Step Relay Module.

• Works with step ballasts to provide multi-level lighting control from a single panel slot.
• Utilizes dual 30A relays that are each de-rated to 16A
• Each module incorporates the latest in “zero-cross” switching technology to greatly extend relay switching life.
• Relay Modules communicate with the Master Interface to report:
  • The relay’s current state (on/off)
  • The line source state (available or off)
  • The communication status (active / not available)
  • The relay’s “health.” (if the relay is defective)

This is the programmable countdown time switch. The RT-100 Programmable Countdown Time Switch automatically turns lighting or other loads off when the programmed on-time expires. It replaces standard single-pole wall switches for energy savings inside and outside.

Users turn connected lights on by pressing the on/off button, which activates the on-time programmed by the installer. If users want the lights to remain on for a different period of time, they simply press and hold the on/off button until the display shows the desired time. When the button is released, the lights will remain on for the newly selected on-time. After the time has elapsed, lighting is automatically turned off. Lights can be turned off before the countdown is complete by pressing the on/ off button.

The on-time can be programmed for 5 to 55 minutes (in 5-minute increments) or 1 to 12 hours (in 15-minute increments). It is typically set for the period of time the connected load normally needs to remain on. Other programming options include enabling or disabling audible and visible shutoff warnings. Check out Wattstopper DLM products here.

• Programmable countdown time switch
• Replaces single-pole switch
• Adjustable on-time from 5 minutes to 12 hours
• Optional audible beep and/or visible light flash warnings before automatic off
• Lighted switch for visibility in darkened rooms
• Low-profile styling
• Choice of five decorator colors
• Operates most common types of lighting
• Relay-based switching
• Zero crossing reduces stress on the relay and increases product longevity
• No current leakage to load in off mode for safety
• Compatible with decorator wall plates

This is the preset countdown time switch. The RT-50 Preset Countdown Time Switch automatically turns lighting or other loads off when the selected on-time expires. It replaces standard single-pole wall switches for energy savings throughout a range of applications.

Users press one of the six preset buttons to turn connected lighting on for the corresponding period of time. After the time has elapsed, lighting is automatically turned off. Lights can be turned off before the countdown is complete by pressing the on/ off button. Users may press the on/off button to turn lights on. The time switch will activate the preset that was last used, and the indicator light for that preset will turn on. To change the countdown, users press the desired preset button and the RT-50 will reset to that countdown interval.

The RT-50 will keep lighting on for 1, 5, 10, 20, 30 or 60 minutes. The digital on-time options provide precise control and help users avoid leaving lights on unnecessarily. Check out Wattstopper DLM products here.

• Seven-button preset time switch
• Replaces single-pole switch
• Selectable on-time: 1, 5, 10, 20, 30, 60 minutes
• Lighted switch for visibility in darkened rooms
• Low-profile styling
• Choice of five decorator colors
• Operates most common types of lighting
• Relay-based switching
• Zero crossing reduces stress on the relay and increases product longevity
• No current leakage to load in off mode for safety
• Compatible with decorator wall plates

This is the RadioRA 2 architectural RF GRAFIK T companion device. RadioRA® 2 architectural RF GRAFIK T local controls function much like standard dimmers or switches, but can be operated as part of a lighting control system. GRAFIK T controls are useful in locations where single circuits of lighting need to be dimmed or switched. All Dimmers, Switches, and Accessories GRAFIK T dimmers and switches contain an Advanced Programming Mode (APM) that allows users to customize the control to meet their specific needs. Check out the RadioRA 2 products page here.

• Controls include dimmers, switches, and companion devices.
• Simple touch control.
• Distinctive architectural aesthetic.
• Softly lit white LEDs indicate light level and coordinate with any décor.
• Advanced microprocessor dimming technology for control of dimmable LED lamps. 1
• Low-end and high-end trim are available for improved LED dimming performance (dimmer only).
• Optional neutral connection available for superior LED dimming performance (C•L® dimmer only). 2
• Phase selectable technology allows forward or reverse phase dimming for compatibility with more load types.
• Installs in single-pole or multi-location applications. Companion devices are available for multi-location control with dimmers and switches (maximum 4 companion devices per dimmer or switch, 1 main control per circuit).
• Use Lutron® GRAFIK TTM wallplates (sold separately). See the Colors and Finishes on page 3 for details.
• Lutron® GRAFIK TTM wallplates snap on with no visible means of attachment.

WattStopper B347D-P Power Packs provide 24VDC operating voltage to all WattStopper 24VDC occupancy sensors and daylighting controllers. Auxiliary Relay Packs are similar to power packs, but only have an isolated relay and no transformer power supply.

B347D-P Power Packs consist of a transformer and high-current relay combined in one small, powerful package. The transformer has a primary high voltage input and a secondary, low voltage output (24 VDC, 114 mA with relay connected). The secondary voltage provides operating power to WattStopper sensors. When the occupancy sensors detect motion or daylighting sensors detect inadequate ambient light, they electrically close an internal circuit, which sends 24 VDC back to the Power or Auxiliary Relay Packs that control the lighting system.

• Self-contained transformer relay system
• Available for 347 volt systems
• Capable of switching up to 20 Amps of electrical load (ballast) at 120/277V for S120/277/347 models, 15A at 347V for all models
• Low voltage leads are teflon coated for use in plenum applications
• Can be used as a low voltage switch for other applications or as stand-alone, low voltage switch

• 1/2 inch snap-in nipple attaches to standard electrical enclosures via 1/2 inch knockouts
• Installation in junction box not required
• Qualifies for ARRA-funded public works projects

• Can be used in conjunction with the following dimmer(s) and switch(es): Maestro®, Maestro IR®, Maestro Wireless®, Pico™ wireless control, Spacer System®, Diva®, Lyneo® Lx, Skylark®, Skylark Contour™
• All Lutron® wallplates are screwless, seamless and have no visible hardware; the front plate securely snaps into the alignment adapter plate
• Full line of wiring devices in designer style opening
• Blank inserts available for Gloss colors (DV-BI-) and Satin colors (SC-BI-)
• Customize your designer wallplate with engraving

• 120/277V
• Paddle turns on/off
• Use with any 15A load
• General purpose switching of all sources and motor loads
• No derating if ganged

• 120V ONLY
• Paddle turns on/off
• Use with any 15A load
• General purpose switching of all sources and motor loads
• No derating if ganged

This is the Satin Wallplate 2-Gang. Check out the RadioRA 2 products page here.

• Can be used in conjunction with the following dimmer(s) and switch(es): Maestro®, Maestro IR®, Maestro Wireless®, Pico™ wireless control, Spacer System®, Diva®, Lyneo® Lx, Skylark®, Skylark Contour™
• All Lutron® wallplates are screwless, seamless and have no visible hardware; the front plate securely snaps into the alignment adapter plate
• Full line of wiring devices in designer style opening
• Blank inserts available for Gloss colors and Satin colors
• Customize your designer wallplate with engraving

This is the Satin Wallplate 3-Gang. Check out the RadioRA 2 products page here.

• Can be used in conjunction with the following dimmer(s) and switch(es): Maestro®, Maestro IR®, Maestro Wireless®, Pico™ wireless control, Spacer System®, Diva®, Lyneo® Lx, Skylark®, Skylark Contour™
• All Lutron® wallplates are screwless, seamless and have no visible hardware; the front plate securely snaps into the alignment adapter plate
• Full line of wiring devices in designer style opening
• Blank inserts available for Gloss colors and Satin colors
• Customize your designer wallplate with engraving

• 120/277V
• Paddle turns on/off
• Use with any 15A load
• General purpose switching of all sources and motor loads
• No derating if ganged