Power packs are the heart of the low voltage sensor system. A PP20 Series power pack transforms
Class I high voltage (120/277 VAC or 347 VAC) to Class 2 15 VDC for powering remote sensors. The
PP20 and the SP20 Series slave pack are also capable of switching lighting loads on and off using
their internal relays. Class 2 wire leads connect to 18 to 22 AWG low voltage cable running to the
sensors, making installation easy and clean. Power packs also have an elongated chase nipple that
allows it to be mounted either directly through a ½ inch knockout into a junction box, or inside an
adjacent box for meeting specific local code requirements in ceiling plenums.
The most versatile power pack is the PP20, which utilizes a patented relay contact protection and
can power up to 14 sensors. Dual-circuit control can be handled by two PP20’s, one PP20 2P Series
2-Pole power pack, or a PP20 power pack and a SP20 slave packs.
FEATURES

•  Powers Low Voltage Sensors (PP20/PP20 2P only)
•  Self-Contained Relay(s) Switch Line Voltage Loads
• Relay Contact Protection
• Plenum Rated

This is a Vive Hub External Power Supply. The Maestro Wireless solution incorporates Maestro Wireless load controls, wireless sensors, and wireless remote controls, which provide a system that delivers energy savings, convenience, and ease of installation. Maestro Wireless dimmers and switches use Lutron patented Clear Connect RF Technology, which enables wireless communication with Radio Powr Savr sensors and Pico remote controls for light control and general switched loads. These products are also compatible with the Vive hub which enables a simple setup process using a standard web browser on any Wi-Fi enabled phone, tablet or computer. It also enables control and monitoring of all Vive devices. The Vive hub can be added at any time and preserves existing system setup by extracting local programming from each device. For a complete list of features supported with the Vive hub, call Lite Rite Controls. Note for Replacement: MRF2S – the “S” model can replace the non-”S” model. Click here to see the Lutron Vive story.

HIGHLIGHTS:

• The Vive Hub External Power Supply provides power to the Vive Hub and Vive Premium Hub.
• Lutron patented Clear Connect RF Technology works through walls and floors.
• Controls include Front Accessible Service Switch (FASSTM) for safe lamp replacement.
• Two-wire installation for any retrofit application.
• Power failure memory: If power is interrupted, the control will return to its previously set level prior to interruption.

System Communications and Capacity

• Maestro Wireless controls communicate with the Pico remote controls and Radio Power Savr
• sensors through radio frequency (RF).
• Receives wireless inputs from up to 10 Pico remote controls, 10 Radio Powr Savr occupancy / vacancy sensors, and 1 Radio Powr Savr daylight sensor
• Maestro Wireless local controls must be located within 60 ft. (18 m) line of sight or 30 ft. (9 m) through walls, of Radio Power Savr sensors.
• Maestro Wireless local controls must be located within 60 ft. (18 m) line of sight or 30 ft. (9 m)
• through walls, of a Pico remote control.
• Up to 10 Maestro Wireless controls can be configured to work together.

Sensors can be assigned to multiple switches.

The PTS 60 and PTS 720 Series Electronic Auto Shut-off Timer Switches provide a simple to use and simple to apply lighting control alternative to wall switch occupancy sensors. These elegant decorator style wall stations each provide six preset countdown timer selections as well as an on/off push-button

• Self-Contained Relay
• Interchangeable Hot & Load Wires – Impossible to Wire Backwards
• No Neutral Connection Required
• Self-Grounding Mounting Strap
• No Minimum Load Requirement
• Push-Button Programmable w/o Removing Switch Plate
• Fixed or Adjustable Preset Times
• Optional Audible Timeout Warning at 45, 30, and 15 sec
• Optional Flicker Timeout Warning at 2 and 1 min
• Continuous LED Flash for Last 30 sec of Button’s Time Setting
• Green On/Off Switch Status LED
• Green LED Time Indicators

• The PTS 60 and PTS 720 Series Electronic Auto Shut-off Timer Switches provide a simple to use and simple to apply lighting control alternative to wall switch occupancy sensors. These elegant decorator style wall stations each provide six preset countdown timer selections as well as an on/off push-button
  • Self-Contained Relay
  • Interchangeable Hot & Load Wires – Impossible to Wire Backwards
  • No Neutral Connection Required
  • Self-Grounding Mounting Strap
  • No Minimum Load Requirement
  • Push-Button Programmable w/o Removing Switch Plate
  • Fixed or Adjustable Preset Times
  • Optional Audible Timeout Warning at 45, 30, and 15 sec
  • Optional Flicker Timeout Warning at 2 and 1 min
  • Continuous LED Flash for Last 30 sec of Button’s Time Setting
  • Green On/Off Switch Status LED
  • Green LED Time Indicators

This is the passive infrared wall switch occupancy sensor. The PW-301 passive infrared (PIR) wall switch sensor can turn lights OFF and ON based on occupancy. It is characterized by high sensitivity to small and large movements, appealing aesthetics, and a variety of features. The PW-301 replaces existing wall switches and installs in a single gang junction box with or without either neutral wiring. Factory default operation is for Manual-ON, so that users turn lights on only when needed. It uses advanced PIR technology to detect occupancy and keep lighting ON when it is needed. Once the space is vacated and the time delay elapses, lights automatically turn OFF. DIP switch settings allow for a variety of control options such as Auto-ON operation, walk-through and test modes. Multiple sensors may be used for control of one or more loads from up to four locations. The PW-301 sensor uses a patent pending Neutral Sense Technology. Any PW-301 sensor can be used for a two-wire or three wire application, either to work with existing wiring, or to meet local or national code requirements. An easy-to-break plastic tab covers neutral screw terminals. Once the sensor is connected to neutral it complies with all codes that restrict current leakage to ground. Check out Wattstopper DLM products here.

• Complies with 2011 NEC requirements
• Zero-crossing for long relay life
• Vandal resistant lens combines precise coverage with durability
• Selectable walk-through mode turns lights off three minutes after the room is initially occupied if no motion is detected after the first 30 seconds
• Test mode allows quick and easy adjustments
• Selectable audible and/or visual alerts for impending shutoff
• LED indicates occupancy detection
• In automatic mode, sensor returns automatically to Auto-ON after lights are turned off manually; ideal for presentations
• Optional light level sensing with simple setup
• Service mode allows sensor to operate as a service switch in the unlikely event of a failure
• Sensor coverage tested to NEMA Guide Publication WD 7-2000
• Compatible with decorator wall plates

This is the passive infrared dual relay wall switch occupancy sensor. The PW-302 passive infrared (PIR) wall switch sensor turns lights ON and OFF based on occupancy. It contains two relays for controlling two independent lighting loads or circuits, and a variety of features. The PW-302 replaces existing wall switches and installs in a single gang junction box with or without either neutral wiring. Each of the PW-302’s relays can control a separate lighting load. The device uses advanced PIR technology to detect occupancy and turn the first relay ON. The other relay must be manually engaged to turn remaining lights on. Once the space is vacated and the time delay elapses, all lights automatically turn OFF. Dual ON/OFF buttons allow the user to manually turn on and off each of the loads. DIP switch settings allow for a variety of control options such as Manual-ON or Auto-ON for each relay, walk-through and test modes. Multiple sensors may be used for control of one or more loads from up to four locations. The PW-302 sensor uses a patent pending Neutral Sense Technology. Any PW-302 sensor can be used for a two-wire or three wire application, either to work with existing wiring, or to meet local or national code requirements. An easy-to-break plastic tab covers neutral screw terminals. Once the sensor is connected to neutral it complies with all codes that restrict current leakage to ground. Check out Wattstopper DLM products here.

• Complies with 2011 NEC requirements
• Zero-crossing on both relays for long relay life
• Vandal resistant lens combines precise coverage with durability
• Selectable walk-through mode turns lights off three minutes after the room is initially occupied if no motion is detected after the first 30 seconds
• Test mode allows quick and easy adjustments
• LED indicates occupancy detection
• Selectable audible and/or visual alerts for impending shutoff
• In automatic mode, sensor returns automatically to Auto-ON after lights are turned off manually; ideal for presentations
• Optional light level sensor holds secondary lights off when ambient lighting is above the preset level
• Service mode allows sensor to operate as a service switch in the unlikely event of a failure
• Sensor coverage tested to NEMA Guide Publication WD 7-2000
• Compatible with decorator wall plates

• Provides control for the following Lutron products that incorporate a wired IR input:
  • Energi Savr Node units
  • QS Sensor Modules
  • EcoSystem ballasts or ballast modules
• Mounts easily in any single-gang wallbox
• Fits designer style Claro wallplates

• Provides control for the following Lutron products that incorporate a wired IR input:
  • Energi Savr Node units
  • QS Sensor Modules
  • EcoSystem ballasts or ballast modules
• Mounts easily in any single-gang wallbox
• Fits designer style Claro wallplates

• Provides control for the following Lutron products that incorporate a wired IR input:
  • Energi Savr Node units
  • QS Sensor Modules
  • EcoSystem ballasts or ballast modules
• Mounts easily in any single-gang wallbox
• Fits designer style Claro wallplates

• Provides control for the following Lutron products that incorporate a wired IR input:
  • Energi Savr Node units
  • QS Sensor Modules
  • EcoSystem ballasts or ballast modules
• Mounts easily in any single-gang wallbox
• Fits designer style Claro wallplates

This is the Single Pole Relay Module.

• Incorporates the latest in “zero-cross” switching technology to greatly extended relay switching life.
• Relay Modules communicate with the Master Interface to report:
  • The relay’s current state (on/off)
  • The line source state (available or off)
  • The line frequency (in Hz)
  • The communication status (active / not available)
  • The relay’s “health.” (if the relay is defective
• Relay Modules are interchangeable with all other RD style relay and dimming modules.

This is the RadioRA 2 remote dimmer. Check out the RadioRA 2 products page here.

• RadioRA 2 Maestro dimmers incorporate advanced features such as fade on/fade off, delayed long fade to off, and rapid full on.
• RadioRA 2 Maestro local controls include a Front Accessible Service Switch (FASS) for safe lamp replacement.
• Use Lutron Designer (Claro or Satin Colors) wallplates or designer-style wallplates from other manufacturers.