• The PTS 60 and PTS 720 Series Electronic Auto Shut-off Timer Switches provide a simple to use and simple to apply lighting control alternative to wall switch occupancy sensors. These elegant decorator style wall stations each provide six preset countdown timer selections as well as an on/off push-button
  • Self-Contained Relay
  • Interchangeable Hot & Load Wires – Impossible to Wire Backwards
  • No Neutral Connection Required
  • Self-Grounding Mounting Strap
  • No Minimum Load Requirement
  • Push-Button Programmable w/o Removing Switch Plate
  • Fixed or Adjustable Preset Times
  • Optional Audible Timeout Warning at 45, 30, and 15 sec
  • Optional Flicker Timeout Warning at 2 and 1 min
  • Continuous LED Flash for Last 30 sec of Button’s Time Setting
  • Green On/Off Switch Status LED
  • Green LED Time Indicators

This is the passive infrared wall switch occupancy sensor. The PW-301 passive infrared (PIR) wall switch sensor can turn lights OFF and ON based on occupancy. It is characterized by high sensitivity to small and large movements, appealing aesthetics, and a variety of features. The PW-301 replaces existing wall switches and installs in a single gang junction box with or without either neutral wiring. Factory default operation is for Manual-ON, so that users turn lights on only when needed. It uses advanced PIR technology to detect occupancy and keep lighting ON when it is needed. Once the space is vacated and the time delay elapses, lights automatically turn OFF. DIP switch settings allow for a variety of control options such as Auto-ON operation, walk-through and test modes. Multiple sensors may be used for control of one or more loads from up to four locations. The PW-301 sensor uses a patent pending Neutral Sense Technology. Any PW-301 sensor can be used for a two-wire or three wire application, either to work with existing wiring, or to meet local or national code requirements. An easy-to-break plastic tab covers neutral screw terminals. Once the sensor is connected to neutral it complies with all codes that restrict current leakage to ground. Check out Wattstopper DLM products here.

• Complies with 2011 NEC requirements
• Zero-crossing for long relay life
• Vandal resistant lens combines precise coverage with durability
• Selectable walk-through mode turns lights off three minutes after the room is initially occupied if no motion is detected after the first 30 seconds
• Test mode allows quick and easy adjustments
• Selectable audible and/or visual alerts for impending shutoff
• LED indicates occupancy detection
• In automatic mode, sensor returns automatically to Auto-ON after lights are turned off manually; ideal for presentations
• Optional light level sensing with simple setup
• Service mode allows sensor to operate as a service switch in the unlikely event of a failure
• Sensor coverage tested to NEMA Guide Publication WD 7-2000
• Compatible with decorator wall plates

This is the passive infrared dual relay wall switch occupancy sensor. The PW-302 passive infrared (PIR) wall switch sensor turns lights ON and OFF based on occupancy. It contains two relays for controlling two independent lighting loads or circuits, and a variety of features. The PW-302 replaces existing wall switches and installs in a single gang junction box with or without either neutral wiring. Each of the PW-302’s relays can control a separate lighting load. The device uses advanced PIR technology to detect occupancy and turn the first relay ON. The other relay must be manually engaged to turn remaining lights on. Once the space is vacated and the time delay elapses, all lights automatically turn OFF. Dual ON/OFF buttons allow the user to manually turn on and off each of the loads. DIP switch settings allow for a variety of control options such as Manual-ON or Auto-ON for each relay, walk-through and test modes. Multiple sensors may be used for control of one or more loads from up to four locations. The PW-302 sensor uses a patent pending Neutral Sense Technology. Any PW-302 sensor can be used for a two-wire or three wire application, either to work with existing wiring, or to meet local or national code requirements. An easy-to-break plastic tab covers neutral screw terminals. Once the sensor is connected to neutral it complies with all codes that restrict current leakage to ground. Check out Wattstopper DLM products here.

• Complies with 2011 NEC requirements
• Zero-crossing on both relays for long relay life
• Vandal resistant lens combines precise coverage with durability
• Selectable walk-through mode turns lights off three minutes after the room is initially occupied if no motion is detected after the first 30 seconds
• Test mode allows quick and easy adjustments
• LED indicates occupancy detection
• Selectable audible and/or visual alerts for impending shutoff
• In automatic mode, sensor returns automatically to Auto-ON after lights are turned off manually; ideal for presentations
• Optional light level sensor holds secondary lights off when ambient lighting is above the preset level
• Service mode allows sensor to operate as a service switch in the unlikely event of a failure
• Sensor coverage tested to NEMA Guide Publication WD 7-2000
• Compatible with decorator wall plates

• Provides control for the following Lutron products that incorporate a wired IR input:
  • Energi Savr Node units
  • QS Sensor Modules
  • EcoSystem ballasts or ballast modules
• Mounts easily in any single-gang wallbox
• Fits designer style Claro wallplates

• Provides control for the following Lutron products that incorporate a wired IR input:
  • Energi Savr Node units
  • QS Sensor Modules
  • EcoSystem ballasts or ballast modules
• Mounts easily in any single-gang wallbox
• Fits designer style Claro wallplates

• Provides control for the following Lutron products that incorporate a wired IR input:
  • Energi Savr Node units
  • QS Sensor Modules
  • EcoSystem ballasts or ballast modules
• Mounts easily in any single-gang wallbox
• Fits designer style Claro wallplates

• Provides control for the following Lutron products that incorporate a wired IR input:
  • Energi Savr Node units
  • QS Sensor Modules
  • EcoSystem ballasts or ballast modules
• Mounts easily in any single-gang wallbox
• Fits designer style Claro wallplates

This is the Single Pole Relay Module.

• Incorporates the latest in “zero-cross” switching technology to greatly extended relay switching life.
• Relay Modules communicate with the Master Interface to report:
  • The relay’s current state (on/off)
  • The line source state (available or off)
  • The line frequency (in Hz)
  • The communication status (active / not available)
  • The relay’s “health.” (if the relay is defective
• Relay Modules are interchangeable with all other RD style relay and dimming modules.

This is the RadioRA 2 remote dimmer. Check out the RadioRA 2 products page here.

• RadioRA 2 Maestro dimmers incorporate advanced features such as fade on/fade off, delayed long fade to off, and rapid full on.
• RadioRA 2 Maestro local controls include a Front Accessible Service Switch (FASS) for safe lamp replacement.
• Use Lutron Designer (Claro or Satin Colors) wallplates or designer-style wallplates from other manufacturers.

This is the RadioRA 2 maestro local control remote switch. Check out the RadioRA 2 products page here.

• On a single-tap, lights or motors turn ON or OFF.
• Neutral and two-wire switches available.

This is the RadioRA 2 maestro local control remote switch. Check out the RadioRA 2 products page here.

• On a single-tap, lights or motors turn ON or OFF.
• Neutral and two-wire switches available.

This is the PIR multi-way wall switch occupancy sensor. The RH-250 Passive Infrared (PIR) Multi-way Occupancy Sensor provides automatic lighting shutoff for a variety of applications including those with multiple switch locations. It offers optional automatic lighting activation. The RH-250 operates either as a manual- or automatic-on sensor. When in manual-on mode, users must press the pushbutton to turn on lighting. The RH-250 employs PIR technology to sense the difference between the infrared energy from a person in motion and the background space. It keeps lighting on as long as motion is detected and provides automatic shutoff, following a user-selected time delay, when motion is no longer detected. Users may turn the lighting off manually. When automatic-on operation has been selected, the adjustable light level sensor may be set to prevent lights from turning on automatically if sufficient daylight is present.

An RH-250 connected to other RH-250s and/or RH-253 Decorator Single Pole Momentary Switches provides true multi-way on/off control. An occupant simply presses the on/ off pushbutton of any connected device to turn on the lighting. Lights remain on as long as one of the RH-250s continues to detect occupancy. The user may turn off the lighting by pressing the on/off button on any of the connected devices. If the room becomes vacant and lights are on, they will be switched off automatically following the time delay of the last RH-250 to detect occupancy. Check out Wattstopper DLM products here.

• Complies with 2011 NEC requirements
• Replaces single- or multi-pole switches
• Provides multi-way control when used with other RH-250s or RH-253s
• Adjustable time delay, 15 seconds to 30 minutes
• Lighted switch for visibility in darkened rooms
• If enabled, light level sensing prevents automatic-on when adequate daylight exists
• Low-profile styling
• Choice of five decorator colors; lens is color-matched to device
• Operates most common types of lighting
• Relay-based switching
• No current leakage to load in off mode for safety
• Compatible with decorator wall plates
• Compliant with Nonresidential CA Title 24 requirements

WS-CaseStudy-GreenHome_OccupancyVacancyTimeswitches