This is the Claro Wallplate 4-Gang. Check out the RadioRA 2 products page here.

• Can be used in conjunction with the following dimmer(s) and switch(es): Maestro®, Maestro IR®, Maestro Wireless®, Pico™ wireless control, Spacer System®, Diva®, Lyneo® Lx, Skylark®, Skylark Contour™
• All Lutron® wallplates are screwless, seamless and have no visible hardware; the front plate securely snaps into the alignment adapter plate
• Full line of wiring devices in designer style opening
• Blank inserts available for Gloss colors and Satin colors
• Customize your designer wallplate with engraving

This is the Claro Wallplate 5-Gang. Check out the RadioRA 2 products page here.

• Can be used in conjunction with the following dimmer(s) and switch(es): Maestro®, Maestro IR®, Maestro Wireless®, Pico™ wireless control, Spacer System®, Diva®, Lyneo® Lx, Skylark®, Skylark Contour™
• All Lutron® wallplates are screwless, seamless and have no visible hardware; the front plate securely snaps into the alignment adapter plate
• Full line of wiring devices in designer style opening
• Blank inserts available for Gloss colors and Satin colors
• Customize your designer wallplate with engraving

This is the 2 channel low voltage dimming module.

• Provide two channels of 0-10V dimming for up (40) ballasts per channel (80 total).
• Combine a two-pole line voltage switching module and a two channel 0-10V dimming module. This completely disconnects the line voltage load from the source automatically when the dimmer is set to 0%.
• Dimming Modules communicate with the Master Interface to report:
  • The dimmer’s current dimming level (0-100%)
  • The line source state (available or off)
  • The communication status (active / not available)
  • The module’s “health” (if the module is defective)
• Interchangeable with all other RD style relay and dimming modules, providing a higher level of flexibility than currently available in the market

This is the Line Voltage & 3-Wire Dimming Module.

• Software configurable for either forward or reverse phase control.
• Utilize a relay ahead of the dimmer for complete disconnection from the source voltage when the dimmer is off.
• Dimming Modules are completely compatible with 3-wire fluorescent dimming ballasts (Hot, Dimmed Hot and Neutral).
• Dimming Modules communicate with the Building Management Server to report:
  • The dimmer’s current dimming level (0-100% on)
  • The line source state (available or off)
  • The communication status (active / not available)
  • The module’s “health” (if the module is defective)

This is the decorator rotary DR series dimmer. Check out the Pass & Seymour products.

• A new style that matches P&S Decorator Combination devices.
• Accepts Snap-In Light Module (sold separately) to convert decorator rotary devices into illuminated-type in moments; makes devices easy to find in the dark.
• Screw-pressure-plate back wiring speeds installation and ensures solid, high-quality electrical connections. Also supports traditional, wire-loop side wiring.
• Heavy-gauge black anodized aluminum strap provides superior heat management and structural strength for mounting against wall surfaces.
• Slim design leaves more room in the box and makes installation faster and easier.
• 1100W single pole
• No de-rating of 700 watt devices.

This is the decorator rotary DR series dimmer. Check out the Pass & Seymour products.

• A new style that matches P&S Decorator Combination devices.
• Accepts Snap-In Light Module (sold separately) to convert decorator rotary devices into illuminated-type in moments; makes devices easy to find in the dark.
• Screw-pressure-plate back wiring speeds installation and ensures solid, high-quality electrical connections. Also supports traditional, wire-loop side wiring.
• Heavy-gauge black anodized aluminum strap provides superior heat management and structural strength for mounting against wall surfaces.
• Slim design leaves more room in the box and makes installation faster and easier.
• 700W single pole
• No de-rating of 700 watt devices.

This is the decorator rotary DR series fan speed control. Check out the Pass & Seymour products.

• A new style that matches P&S Decorator Combination devices.
• Accepts Snap-In Light Module (sold separately) to convert decorator rotary devices into illuminated-type in moments; makes devices easy to find in the dark.
• Screw-pressure-plate back wiring speeds installation and ensures solid, high-quality electrical connections. Also supports traditional, wire-loop side wiring.
• Heavy-gauge black anodized aluminum strap provides superior heat management and structural strength for mounting against wall surfaces.
• Slim design leaves more room in the box and makes installation faster and easier.
• 700W single pole
• No de-rating of 700 watt devices.

This is the decorator rotary DR series fan speed control. Check out the Pass & Seymour products.

• A new style that matches P&S Decorator Combination devices.
• Accepts Snap-In Light Module (sold separately) to convert decorator rotary devices into illuminated-type in moments; makes devices easy to find in the dark.
• Screw-pressure-plate back wiring speeds installation and ensures solid, high-quality electrical connections. Also supports traditional, wire-loop side wiring.
• Heavy-gauge black anodized aluminum strap provides superior heat management and structural strength for mounting against wall surfaces.
• Slim design leaves more room in the box and makes installation faster and easier.
• 5A  single pole 3-way fan speed control.

This is the dual technology wall switch sensor w/ 2-relays. The DSW-200 dual technology wall switch sensor turns lights ON and OFF based on occupancy and contains two relays for controlling two independent lighting loads or circuits. It combines the benefits of passive infrared (PIR) and ultrasonic detection technologies for high sensitivity to small and large movements. The DSW-200 replaces existing wall switches and fits a standard decorator wall plate.

Each of the DSW-200’s relays can control a separate lighting load. By default, when the PIR sensor detects occupancy, relay 1 turns ON automatically. Detection by either PIR or ultrasonic technology holds lights ON. When occupancy is no longer detected and the time delay elapses, lights automatically turn OFF. Dual ON/OFF buttons allow the user to turn on and off each of the loads manually. DIP switch settings allow for a variety of control options such as Auto-ON or Manual-ON for each relay, walk-through, and test mode. Check out Wattstopper DLM products here.

This is the dual technology wall switch occupancy sensor. The DSW-301 dual technology wall switch sensor turns lights OFF and ON based on occupancy. It combines the benefits of passive infrared (PIR) and ultrasonic detection technologies. The DSW-301 replaces existing wall switches and fits behind a standard decorator wall plate. Once the lights are ON, detection by either technology holds lights ON until occupancy is no longer detected and the time delay elapses. Factory default operation is for Manual-ON, so that users must turn lights on. DIP switch settings allow for a variety of control options including Auto-ON operation, walk-through and test mode. In Auto-ON mode, the DSW-301 turns lighting on when the PIR sensor detects occupancy. Additional DIP switch settings allow the user to choose which sensing technologies hold ON or retrigger the lighting. Multiple sensors may be used for control of one or more loads from up to four locations. The DSW-301 sensor uses a patent pending Neutral Sense Technology. Any DSW-301 sensor can be used for a two-wire or three wire application, either to work with existing wiring, or to meet local or national code requirements. An easy-to-break plastic tab covers neutral screw terminals. Once the sensor is connected to neutral it complies with all codes that restrict current leakage to ground. Check out Wattstopper DLM products here.

• Complies with 2011 NEC requirements
• Zero-crossing for long relay life
• Vandal resistant lens combines precise coverage with durability
• Selectable walk-through mode turns lights off three minutes after initial occupancy if no motion is detected after the first 30 seconds
• Test mode allows quick and easy adjustments
• Selectable audible alert for impending shutoff
• In automatic mode, sensor returns automatically to Auto-ON after lights are turned off manually; ideal for presentations
• Four occupancy logic options to customize control to meet application needs
• Optional light level sensing with simple setup
• Service mode allows sensor to operate as a service switch in the unlikely event of a failure
• Sensor coverage tested to NEMA Guide Publication WD 7-2000

This is the dual technology dual relay wall switch occupancy sensor. The DSW-302 dual technology wall switch sensor turns lights ON and OFF based on occupancy and contains two relays for controlling two independent lighting loads or circuits. It combines the benefits of passive infrared (PIR) and ultrasonic detection technologies for high sensitivity to small and large movements. The DSW-302 replaces existing wall switches and fits a standard decorator wall plate. Each of the DSW-302’s relays can control a separate lighting load. By default, when the PIR sensor detects occupancy, relay 1 turns ON automatically. Remaining lighting must be turned on manually. Detection by either PIR or ultrasonic technology holds lights ON. When occupancy is no longer detected and the time delay elapses, lights automatically turn OFF. Dual ON/ OFF buttons allow the user to turn on and off each of the loads manually. DIP switch settings allow for a variety of control options such as Auto-ON or Manual-ON for each relay, walkthrough, and test mode. Multiple sensors may be used for control of one or more loads from up to four locations. The DSW-302 sensor uses a patent pending Neutral Sense Technology. Any DSW-302 sensor can be used for a two-wire or three wire application, either to work with existing wiring, or to meet local or national code requirements. An easy-to-break plastic tab covers neutral screw terminals. Once the sensor is connected to neutral it complies with all codes that restrict current leakage to ground. Check out Wattstopper DLM products here.

• Complies with 2011 NEC requirements
• Zero-crossing on both relays for long relay life
• Vandal resistant lens combines precise coverage with durability
• Selectable walk-through mode turns lights off three minutes after the room is initially occupied if no motion is detected after the first 30 seconds
• Selectable audible alert for impending shutoff
• In automatic mode, sensor returns automatically to Auto-ON after lights are turned off manually; ideal for presentations
• Test mode allows quick and easy adjustments
• Four occupancy logic options to customize control to meet application needs
• Optional light level sensor holds secondary lights off when ambient lighting is above the preset level
• Service mode allows sensor to operate as a service switch in the unlikely event of a failure
• Sensor coverage tested to NEMA Guide Publication WD 7-2000